Sto cercando di utilizzare un Arduino Leonardo per l'emulazione da tastiera poiché questa è una delle sue funzioni pubblicizzate. Ho giocato con Leonardo e ho scritto uno schizzo molto semplice basato sull'esempio di Blink.Emulazione tastiera generica con Arduino Leonardo
// Pin 13 has an LED connected on most Arduino boards.
int led = 13;
// The setup routine runs once when you press reset:
void setup()
{
// Initialize the digital pin as an output.
pinMode(led, OUTPUT);
}
// The loop routine runs over and over again forever:
void loop()
{
delay(5000); // Wait for five seconds
digitalWrite(led, HIGH); // Turn the LED on (HIGH is the voltage level)
delay(100); // Wait for a secondA
digitalWrite(led, LOW); // Turn the LED off by making the voltage LOW
Keyboard.write('A'); // Write an A using keyboard emulator
}
Ora questo esempio funziona perfettamente sul mio computer Windows XP. È riconosciuto come una tastiera generica HID e digiterà una "A" ogni cinque secondi.
L'ambiente di destinazione è in esecuzione DOS quindi per quanto ne so ho bisogno di ottenere l'Arduino Leonardo riconosciuto dal BIOS su questa macchina, che non è e non digita il 'A' in DOS.
Ho apportato modifiche al descrittore del dispositivo USB del Leonardo, cercando di farlo corrispondere un Dell L100 il più possibile. Le modifiche che ho apportato non mi hanno aiutato, e sospetto che sia perché Leonardo è un dispositivo composito che espone la comunicazione seriale, l'emulazione della tastiera e l'emulazione del mouse sulla stessa porta USB. Il codice sorgente per il descrittori USB/configurazione è disponibile per essere modificato e si trova in:
- Arduino_Installation \ hardware \ arduino \ core \ arduino \ HID.cpp
- Arduino_Installation \ hardware \ arduino \ core \ arduino \ USBDesc.h
- Arduino_Installation \ hardware \ arduino \ core \ arduino \ USBCore.h
- Arduino_Installation \ hardware \ arduino \ core \ arduino \ USBCore.cpp
La seguente è una discarica da dispositivo USBVisualizzatore per Leonardo:
[Port3] : USB Composite Device
---===>Device Information<===---
English product name: "Arduino Leonardo"
ConnectionStatus:
Current Config Value: 0x01 -> Device Bus Speed: Full
Device Address: 0x03
Open Pipes: 4
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x81 -> Direction: IN - EndpointID: 1
bmAttributes: 0x03 -> Interrupt Transfer Type
wMaxPacketSize: 0x0010 = 0x10 bytes
bInterval: 0x40
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x02 -> Direction: OUT - EndpointID: 2
bmAttributes: 0x02 -> Bulk Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x00
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x83 -> Direction: IN - EndpointID: 3
bmAttributes: 0x02 -> Bulk Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x00
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x84 -> Direction: IN - EndpointID: 4
bmAttributes: 0x03 -> Interrupt Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x01
===>Device Descriptor<===
bLength: 0x12
bDescriptorType: 0x01
bcdUSB: 0x0110
bDeviceClass: 0x00
*!*ERROR: device class should be Multi-interface Function 0xEF
When IAD descriptor is used
bDeviceSubClass: 0x00
*!*ERROR: device SubClass should be USB Common Sub Class 2
When IAD descriptor is used
bDeviceProtocol: 0x00
*!*ERROR: device Protocol should be USB IAD Protocol 1
When IAD descriptor is used
bMaxPacketSize0: 0x40 = (64) Bytes
idVendor: 0x2341 = Vendor ID not listed with USB.org as of 03-19-2008
idProduct: 0x8036
bcdDevice: 0x0100
iManufacturer: 0x01
English (United States) "Arduino LLC"
iProduct: 0x02
English (United States) "Arduino Leonardo"
iSerialNumber: 0x00
bNumConfigurations: 0x01
===>Configuration Descriptor<===
bLength: 0x09
bDescriptorType: 0x02
wTotalLength: 0x0064 -> Validated
bNumInterfaces: 0x03
bConfigurationValue: 0x01
iConfiguration: 0x00
bmAttributes: 0x80 -> Bus Powered
MaxPower: 0xFA = 500 mA
===>IAD Descriptor<===
bLength: 0x08
bDescriptorType: 0x0B
bFirstInterface: 0x00
bInterfaceCount: 0x02
bFunctionClass: 0x02 -> This is Communications (CDC Control) USB Device Interface Class
bFunctionSubClass: 0x01
bFunctionProtocol: 0x01
iFunction: 0x00
===>Interface Descriptor<===
bLength: 0x09
bDescriptorType: 0x04
bInterfaceNumber: 0x00
bAlternateSetting: 0x00
bNumEndpoints: 0x01
bInterfaceClass: 0x02 -> This is Communications (CDC Control) USB Device Interface Class
bInterfaceSubClass: 0x01
bInterfaceProtocol: 0x00
CAUTION: This may be an invalid bInterfaceProtocol
iInterface: 0x00
-> This is a Communications (CDC Control) USB Device Interface Class
===>Descriptor Hex Dump<===
bLength: 0x05
bDescriptorType: 0x24
05 24 00 10 01
-> This is a Communications (CDC Control) USB Device Interface Class
===>Descriptor Hex Dump<===
bLength: 0x05
bDescriptorType: 0x24
05 24 01 01 01
-> This is a Communications (CDC Control) USB Device Interface Class
===>Descriptor Hex Dump<===
bLength: 0x04
bDescriptorType: 0x24
04 24 02 06
-> This is a Communications (CDC Control) USB Device Interface Class
===>Descriptor Hex Dump<===
bLength: 0x05
bDescriptorType: 0x24
05 24 06 00 01
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x81 -> Direction: IN - EndpointID: 1
bmAttributes: 0x03 -> Interrupt Transfer Type
wMaxPacketSize: 0x0010 = 0x10 bytes
bInterval: 0x40
===>Interface Descriptor<===
bLength: 0x09
bDescriptorType: 0x04
bInterfaceNumber: 0x01
bAlternateSetting: 0x00
bNumEndpoints: 0x02
bInterfaceClass: 0x0A -> This is a CDC Data USB Device Interface Class
bInterfaceSubClass: 0x01
bInterfaceProtocol: 0x00
CAUTION: This may be an invalid bInterfaceProtocol
iInterface: 0x00
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x02 -> Direction: OUT - EndpointID: 2
bmAttributes: 0x02 -> Bulk Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x00
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x83 -> Direction: IN - EndpointID: 3
bmAttributes: 0x02 -> Bulk Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x00
===>Interface Descriptor<===
bLength: 0x09
bDescriptorType: 0x04
bInterfaceNumber: 0x02
bAlternateSetting: 0x00
bNumEndpoints: 0x01
bInterfaceClass: 0x03 -> HID Interface Class
bInterfaceSubClass: 0x01
bInterfaceProtocol: 0x00
CAUTION: This may be an invalid bInterfaceProtocol
iInterface: 0x00
===>HID Descriptor<===
bLength: 0x09
bDescriptorType: 0x21
bcdHID: 0x0101
bCountryCode: 0x00
bNumDescriptors: 0x01
bDescriptorType: 0x22
wDescriptorLength: 0x0065
===>Endpoint Descriptor<===
bLength: 0x07
bDescriptorType: 0x05
bEndpointAddress: 0x84 -> Direction: IN - EndpointID: 4
bmAttributes: 0x03 -> Interrupt Transfer Type
wMaxPacketSize: 0x0040 = 0x40 bytes
bInterval: 0x01
Come è possibile ottenere questo Leonardo riconosciuto da un BIOS come una tastiera generica?
Hai una soluzione ?. Ho lo stesso problema. – Delta
Io no. Ho provato la soluzione fornita da darBis, ma non è riuscita a far riconoscere il PC. –